Announcement

Collapse
No announcement yet.

Power Supplies

Collapse
This is a sticky topic.
X
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Power Supplies

    Who uses aftermarket power for thier current layouts?

    I have used standard set power, 1 pack per lane, for years. Now I have decided to go with an adustable power supply, that allows me to turn down the voltage, enabling folks just getting started, or younger children to perhaps enjoy the cars abit more, without excess damage to them!

    If you are using them, what brands do you use?

    hat:Harry

  • #2
    Radio Shack 3 amp regulated 13.x volts.
    Timer has a separate power supply (original Ninco) as it likes a different voltage.

    Dan

    Comment


    • #3
      I use a 10 AMP 0 to 21 volt ajustable regulated power supply..
      It works great because you can change voltage when racing diferent type cars...

      Comment


      • #4
        Ah yes. My favorite topic. Power supplies. I have what you would call a frankenstien type power supply. It is a Cosel 17am 15V DC regulated power supply. The AC filtering is an off the shelf unit. It is wired for direction selection on either lane and dynamic braking. My dynamic braking though is broken. It blows up my fuses. So I think I have a bad wiring job from power to ground. The great thing about aftermarket powersupplies is the ability to run more "stuff" on your cars without worrying about voltage drop. You can run LED's until you go blind, run a Falcon motor, and run your blender (for those adult bevarages) all on one lane! Maybe not the blender. My power supplies is partially adjustable. I have to set a potentiameter to adjust the power output.

        mario-

        Comment


        • #5
          I see most of you are using regulated supplies. What you would really want in a slot car power supply is a non-regulated power supply or a linear regulated supply, not a fully regulated supply. Believe me this info has been learned from setting up the tracks here in the Detroit area with the guidance of Professor Motor. The way a regulated supply works is as power is required or used, the unit will increase or push up the voltage to try and maintain the initial voltage setting. Compared to a non-regulated supply you will find that your cars motor will run hotter and you will need to have your initial voltage level set lower than a non-regulated supply. My track uses a custom built power supply built by Professor Motor that has four independent non-regulated power supplies (one for each lane) and each can be adjusted from 0-20 volts independently. Some others in the area are using a 0-15 volt 20 amp linear regulated supply, which the good Professor recommends if you cannot go the non-regulated route. At least four of these are being used on area tracks with good results. Here is a link: www.mpja.com/product.asp?...t=12640+PS
          With my track powered by a non-regulated power source I find that I can run the power a couple of volts higher say at 15 volts, and the cars still run cooler than at the tracks powered by the regulated supplies set at 13 volts. I'm not an electronics expert but I sure do trust Professor Motor's advice when it comes to power supplies and slot cars.

          3D

          Comment


          • #6
            Hey Harry, does that power supply look familiar???

            Hope you like it.

            mario-

            **** I'm good.

            Comment


            • #7
              The issue of non-regulated and regulated supplies are very application dependant. With a regulated supply, you'll have the ability to maintain a certain level of voltage. A non-regulated supply will drop voltage under load. For my home usage, my regulated supply works great. So the cooler motors are because of the drop in voltage. You may not be getting 15V to the motor.

              With that all being said, can someone give their definition of a linear supply? I have bounced this thread to our PH.d here at work and his statement was:

              "If you have beefy enough supply, none of this matters."

              With that being said, if your supply gives you enough voltage and current to run any of your motors in your stable you should be fine. The main thing is to have equal and clean power to each lane.

              Comment


              • #8
                Yep it sure does...thats the one I purchased as well. Mario pointed the way for me about a week or so back. Thanks for the info 3D.

                :hat Harry

                Comment


                • #9
                  For my HO is use a Samlex PSA-305, 0-30V, 5amp and for the 1/32 I use a MG #PS10AD, 0-20V, 10amp. I threw away the terminal strips and soldered the connections to the track and ran jumpers to the beginning of all straights. The best investment I ever made was purchasing these supplies. I run the magnet cars at 15v and the non-magnets at 12v. Both lanes have equal power and I don't have anymore voltage drop. When my 6 yr. old daughter wants to "race" I turn it down to 10v and let them fly!

                  Comment


                  • #10
                    Here is my supply best thing i bought for my track..

                    Comment


                    • #11
                      Here is the "FrankenSlotter" ZURICH supply we purchased, as mentioned earlier in this thread. $159.00

                      Everytime Mario sees it, he gets a tear in his eye...

                      Comment


                      • #12
                        What an Anniversary gift, can't wait to try it.

                        It will be a big help in keeping cars in good shape when
                        we have others who want to race but think they have to run all cars full bore even thru the curves.

                        Cindy

                        Comment


                        • #13
                          *tearing*

                          That is a beautiful thing.

                          mario-

                          Comment


                          • #14
                            Hello,
                            At Partsexpress.com, they have a Pyramid 22 amp continuous power supply for $99.90. It features adjustable voltage 6-15 and a built in fan. Part #120-548. It looks like a good one to use for slots.

                            Brian

                            Comment


                            • #15
                              Hello all,
                              I have a dual output (0-30V x 2 @ 2A) bench power supply with digital read-outs for volts and amps. www.web-tronics.com/dualout03x22.html

                              This is attached to a 60' Ninco layout with the dual power track piece.

                              This puts independent variable power to each lane in one neat unit..which is great when my young ones want to race (a 2 and 4 year old). I can regulate the lanes to their abilities.. keeping the cars on the track, and my repair time down.... :-)

                              -Bob

                              Comment

                              Working...
                              X