Announcement

Collapse
No announcement yet.

Race Haven 1/24 Scale Enduro!

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Race Haven 1/24 Scale Enduro!

    Hello All,

    The Rules

    Chassis - Any 1/24 Scale car from BRM, Scaleauto, Plafit, Scholer, DoSlot, Werks, Slotfabrik, or NDW are permitted. If you have a 1/24 Scale car and are unsure of eligibility please PM me. Minimum ride height at ALL times on ALL cars is 1.5mm. Any lower post race and you will be Disqualified.

    Tires - Open - Tires will be checked on glass for any residue or traction additives. If your tires leave a mark on glass then they will have to be cleaned or an alternate set of tires must be used. We also have stock of new tires at the store from both BRM and Scaleauto.

    Motor - Any FK130, FK180, or FC130. **No Falcon 7** Amp Draw on ANY approved motor must be under 2 Amps.

    Body - Any 1/24 or 1/25 Scale Body made of hard plastic. (No Lexan) Bodys must have a detailed and painted interior.

    The Format

    There will be 2 Races. One North Loop, the second will run South Loop. 5 Lanes, 11 Volts, 8 minute Heats with a break at 4 minutes for a driver change. This will total 80 minutes of racing. The result from both races will be totaled and this will decide the Winner or Winning Team.

    Team or Iron Man, Up to you.

    The Entry Fee

    FREE FREE FREE! Bring a few bucks so we can order Pizzas.


    Any questions? Ask away!

    Ron
    Race Haven Hobbies
    www.racehavenhobbies.com
    Last edited by Pro Stock; 11-02-2015, 12:20 PM.

  • #2
    not familiar with the motors, where do you get them?
    Are they fox type motors?

    interesting format.

    What type of controller connectors does your track have?

    Terry

    Comment


    • #3
      Hi Terry,

      The designations refer to standard 1/32 Scale motors. Shark or Boxer type in more familiar terms. What I am getting at is no 16D's and such.

      Sealed endbell Shark (S-Can) or Boxer type motors only. Fox motors are fine.....technically they are a FK130.

      Alligator clips or 4mm bullet style connectors work here.

      Hope to see you out!

      Ron
      Race Haven Hobbies
      www.racehavenhobbies.com

      Comment


      • #4
        I have 13 d motors primarily, falcons 7's and such. I'll have a look in the mess downstairs for the others.

        I'll send a link to the boys from Brants....although I'm not sure they all have meccano type chassis.

        GT, sports car, nascar, short track, modifieds, are all good?

        Terry

        Comment


        • #5
          Any body goes as long as it is closed wheel. The 13D's and Falcon 7's are too hot for our power supply. I have a Few cheap Fox 10 motors here if need be Terry. Check with the Brant gang. It would be great to have a bunch of them out!

          Jim should be down for sure if he dosn't have anything else going on.

          Ron

          Comment


          • #6
            This sounds awesome Ron, count me in!!!

            Comment


            • #7
              Well sounds good... time to do some tweeking...

              Tim Snyder

              Comment


              • #8
                Yes! This is going to be Big. I can smell it.

                Ron
                Race Haven Hobbies
                www.racehavenhobbies.com

                Comment


                • #9
                  Well now the question is what body to run???



                  Or New or old GT 40, may even see the introduction of the C5 Fire Belcher...


                  Tim Snyder

                  Comment


                  • #10
                    The Fast one Timmy.......Always the Fast one.

                    Ron

                    Comment


                    • #11
                      They are all Fast!!!! And long lasting!!!!

                      Tim

                      Comment


                      • #12
                        Lol.......they better be. I am not sure if any of my cars will make 80 minutes of racing!

                        Ron

                        Comment


                        • #13
                          Well i will have to decide between 2 Porsche's and 2 Ford's... all Scholer chassis. Decision time on Sunday for motors...

                          When will you open on Sun. usual 11am???

                          Tim

                          Comment


                          • #14
                            Yes Sir! 11am sharp. See ya then.

                            I want to start the race at 1pm.

                            Ron
                            Race Haven Hobbies
                            www.racehavenhobbies.com

                            Comment


                            • #15
                              After reading the extensive rule booklet i noticed that i had made a serious mistake in my choice of cars. Since we will be running both clockwise and counter clockwise i realized that fueling may be an issue. That being the case i had to speed up the prep of my small block GT40 which has provision to fuel on either side...

                              The body has at the time of this post just come out of the spray booth and is looking interesting. Sealing, decal placement and then sealing again will proceed in the morning. Motor and chassis should roll out of the fab shop later in the day. Since i had a Plafit SLP1 that i had never used, it's time to put it to a test.

                              Tim

                              Comment

                              Working...
                              X