No announcement yet.

PSSRA Group C Specifications

This topic is closed.
This is a sticky topic.
  • Filter
  • Time
  • Show
Clear All
new posts

  • PSSRA Group C Specifications

    2017 Technical Rules for “Group C” Cars
    The objective of this document is to rule the Slot it “Group C” category

    0 - Approved Cars
    0.1 The approved models are: Porsche 956C & KH, Porsche 962C & KH, Sauber Mercedes C9, Jaguar XJR6, 9 or 12, Lancia LC2 & LC2/85, Mazda 787B, Nissan R89C, Toyota 88C.
    0.2 Any modification, substitution or omission may be made only if clearly ruled by this document. Sometimes the prohibitions are explicitly reaffirmed for clarity.
    0.3 The traction magnet must be removed.
    0.4 The maximum width, measured at the tire, is respectively 62.5 mm and 63.5 mm at the front axle and rear axle. The wheels, tires or inserts must not be visible outside the body when viewed from above under any circumstances.
    0.5 The minimum distance between the gear and the track must be at least 1.0 mm.

    1 – Configuration
    1.1 "Group C "The motor chassis (pod) must be 0.0 mm offset CH13 or CH13b; or 0.5 mm offset CH70 with either aluminum 15.8 mm wheels coded PA24Al, PA17Al or 16.5mm wheels coded PA43Al.

    2 – Body & Modifications
    2.1 The body cannot be modified.
    2.1.1 It is acceptable to omit:
    § Mirrors
    § Wipers
    § Sidelights
    § Front towing eye (also from the chassis)
    § Additional lights
    § Antennae
    2.2 The re-painting of the existing body livery is optional and must cover the outer surface only.
    2.3 The painting of white bodies is mandatory and must cover the outer surface only.
    2.4 It is forbidden to paint the transparent parts (except where it was painted on the real car like the top of the windshield, etc.)
    2.5 The body posts for fastening to the chassis can be reinforced by means of a plastic ring.
    2.6 The body must be fixed to the chassis with all the screws as in the stock car.
    2.7 All parts included in the stock car and planned for the specific model can be used.
    2.7.1 "Tear proof" components designed for the specific model may be used. The Sauber, Toyota and the Mazda may use the Jaguar tear proof rear wing. If the Jaguar rear wing is used, the wing may be modified to fit on the post, but the body must remain unmodified.
    2.8 Rear wing attachment to the body may be reinforced with glue, resin and/or tape provided that the body shape is not modified and the reinforcement is not on the wing’s upper surface.
    2.9 Multipiece bodies may be reinforced with ShoeGoo.

    3 – Chassis and modifications
    3.1 All EVO and EVO 6 Chassis can be used.
    3.2 The Chassis is the entire assembled set of the original components.
    3.3 The front axle supports (cups) are optional. It is allowed to thin their sides for the proper insertion on the chassis pins.
    M2 grub screws can be used in their assigned location to adjust the front axle ride height.

    3.5 The front axle plastic bushings of EVO6 chassis are optional. M2 grub screws can be used In their assigned locations to adjust the axle position.
    3.6 The maximum width of the elongated holes for the screws holding the body is 2.6 mm including the washer when present.
    3.7 The maximum width of the elongated holes for the screws holding the motor chassis is 2.6 mm including the washer when present.
    3.8 The two triangular chassis inserts may be glued and/or the tabs melted in place if used or they may be removed.

    4 – Motor Chassis (Pod) and Modifications
    4.1 The motor chassis must be 0.0 mm offset CH13 or CH13b; or 0.5mm offset CH70 and cannot be modified. Flashing and casting imperfections may be lightly sanded.
    4.2 The original rear bushings CH14 can be replaced by the bushings coded CH56.
    4.3 Bushings cannot be glued in their housing.

    5 – Axles and Gears
    5.1 Solid steel shafts coded PA01, PA01-45/48/50 are allowed only.
    5.2 Axles may be trimmed.

    5.3 Stock 9-28 ratio or optional 9-26 may be used.

    6 – Wheels
    6.1. Front wheels must be PA17Pl or PA17Al. 6.2 Rear Wheel diameter 15.8 mm coded PA24Al, PA17Al or 16.5 mm, coded PA43Al.
    6.3 The wheel to tire contact surface must be original and clean.
    6.4 The use of Group C wheel inserts is mandatory.6.5 The “Venturi” cap of PA21 wheel cover can be omitted.

    7 - Tires
    7.1 The compound must maintain the original characteristics; hence any maneuver that may alter its nature, such as treatment with liquids or other substances, is forbidden.
    7.1.1 The identification mark "" must always be present and clearly recognizable.
    7.2 Front tires
    7.2.1 The stock tires coded 1159C1 or PT1027Z0 (formerly PT07) can be installed.
    7.2.2 Tires cannot be glued to the wheel
    7.2.3 The minimum diameter of the front tire mounted on the wheel is 17.8 mm, the diameter shall be uniform across the width.

    7.2.4 The identification mark "" must always be present and clearly recognizable.
    7.3 Rear Tires

    7.3.1 Tires cannot be glued to the wheel. Rear tires N-22 PT1171N22 compound 20 x 10 must be used.

    8 – Motor

    8.1 Only Orange-can 21,500 rpm motor is allowed.
    8.2 The motor cannot be glued nor secured with tape to the chassis or the motor chassis. However, it can be fastened to the motor chassis with screws located in the assigned locations.

    8.3 It is forbidden to modify the motor or make any maneuver that may affect the performance, including breaking in using any type of liquid.
    8.4 S-can motor shafts may be trimmed if found to interfere with the interior.

    9 – Screws, Washers and Spacers
    9.1 The screws must be or metallic appearing.
    There must be as many screws as in the original car, at the assigned locations, and maintaining the original function.
    9.2 Screws may be left loose or tightened.
    9.3 Spacers at the front axle are allowed, as long as metallic and provided that the complete axle assembly width does not exceed the maximum set value.
    9.4 One washer only can be used on each screw at each location as in the stock car.
    9.5 Loctite or similar glue may be used to affix screws. Body must be removable for tech inspection.

    10 – Pick-up
    10.1 The allowed pick up codes are:
    § CH26 § CH10 § CH66
    10.2 A grub screw may be used in the CH66 pick up shaft.
    10.3 A grub screw may be used inside each CH66 braid housing.

    11 – Wiring, Braids and Eyelets
    11.1 The power cables, braids and eyelets to hold the power cables should be Slot.It or Slot.It appearing.

    12 – Ballast
    12.1 Ballast may be used.
    12.2 Weight may not be placed on the outside of the chassis or body.

    13 – Interior
    13.1 Must use stock or replacement full interior specific to the model entered.

    Final Rule, if it does not mention it, it means you cannot do it.
    Last edited by The Professor; 09-26-2016, 03:59 PM. Reason: Updated tire spec
sex vidio
antalya escort
lara escort escort istanbul escort sirinevler escort antalya
atasehir escort taksim eskort lara eskort bayan bakirkoy bayan eskort
gaziantep escort
gaziantep escort
erotik film izle Rus escort gaziantep rus escort
istanbul escort
kadikoy escort kartal escort
Blonde and brunette dirty 3some in semi obscure Профессор трахнул студенту толстым хером pelicula embarazada por accidente