No announcement yet.

PSSRA LeMans Prototype/LMP Specifications

This topic is closed.
This is a sticky topic.
  • Filter
  • Time
  • Show
Clear All
new posts

  • PSSRA LeMans Prototype/LMP Specifications

    0– Approved Cars
    Aston Martin DBR1-2, Audi:R8 LMP, R18 TDI, Lola B09/60-10/60-11/80.
    0.1 Any modification, substitution or omission may be made only if clearly ruled by this document. Sometimes the prohibitions are explicitly reaffirmed for clarity.
    0.2 The traction magnet must be removed.
    0.3 The wheels, tires or inserts must not be visible outside the body when viewed from above under any circumstances.
    0.4 The minimum distance between the gear and the track must be at least 1.0 mm. If a car is found to have “excessive” downforce due to excessive trueing this may be revised to ensure fair competition.

    1 – Configuration
    1.1 “Modern LeMans Prototype” or “LMP" category.

    2 – Body & Modifications
    2.1 The body cannot be modified.
    2.1.1 It is acceptable to omit: Mirrors, Wipers, Sidelights, Front towing eye, (also from the chassis), Additional lights, Antennae.
    2.2 The re-painting of the existing body livery is optional and must cover the outer surface only.
    2.3 The painting of white bodies is mandatory and must cover the outer surface only.
    2.4 It is forbidden to paint the transparent parts (except where it was painted on the real car like the top of the windshield, etc.)
    2.5 The body posts for fastening to the chassis can be reinforced by means of a plastic ring.
    2.6 The body must be fixed to the chassis with all the screws as in the stock car.
    2.7 All parts included in the stock car and planned for the specific model can be used.
    2.7.1 "Tear proof" components designed for the specific model may be used.

    3 – Chassis and modifications

    3.1 All EVO and EVO 6 Chassis can be used.
    3.2 The Chassis is the entire assembled set of the original components.
    3.3 The front axle supports (cups) are optional. It is allowed to thin their sides for the proper insertion on the chassis pins.
    3.4 M2 grub screws can be used in their assigned location to adjust the front axle ride height.
    3.5 The front axle plastic bushings of EVO6 chassis are optional. M2 grub screws can be used in their assigned locations to adjust the axle position.
    3.6 The maximum width of the elongated holes for the screws holding the body is 2.6 mm including the washer when present.
    3.7 The maximum width of the elongated holes for the screws holding the motor chassis is 2.6 mm including the washer when present.
    3.8 The two triangular chassis inserts may be glued and/or the tabs melted in place if used or they may be removed.
    3.9 Tape may only be used to retain the body screws. Tape or any other material may not be used to control movement of any chassis components, only screws or suspension where allowed.

    4 – Motor Chassis (Pod) and Modifications
    4.1 The motor chassis (Anglewinder pod) CH74 cannot be modified. Flashing and casting imperfections may be lightly sanded.
    4.2 The rear bushings CH56 cannot be glued in their housing.

    5 – Axles and Gears
    5.1 Solid steel shafts coded PA01-/50/54
    5.2 Stock 11:28 gear ratio

    6 – Wheels
    6.1 Front Wheels: PA18PL or PA18AL
    6.2 Rear Wheels coded PA62ALS
    6.3 The wheel to tire contact surface must be original and clean.
    6.4 The use of “Modern LMP” wheel inserts is mandatory.

    7 – Tires
    7.1 Front tires:
    7.1.1 The stock tires or PT1027Z0 (formerly PT07) can be installed.
    7.1.2 Front tires cannot be glued to the wheel. The compound must maintain the original characteristics; hence any maneuver that may alter its nature, such as treatment with liquids or other substances, is forbidden.
    7.1.4 The identification mark "" must always be present and clearly recognizable.
    7.2 The rear tires must be the N-22 20 x 10 PT1171N22. They can be glued to the rim.

    8 – Motor
    8.1 MN09H 20.5K Yellow Flat-6 closed can motors.
    8.2 The motor cannot be secured with tape to the chassis or the motor chassis. However, it can be fastened to the motor chassis with screws located in the assigned locations
    8.3 It is forbidden to modify the motor or make any maneuver that may affect the performance, including breaking in using any type of liquid.

    9 – Screws, Washers and Spacers
    9.1 The screws must be or metallic appearing. There must be as many screws as in the original car, at the assigned locations, and maintaining the original function.
    9.2 Screws may be left loose or tightened.
    9.3 Spacers at the front axle are allowed, as long as metallic and provided that the complete axle assembly width does not exceed the maximum set value.
    9.4 One washer only can be used on each screw at each location as in the stock car.
    9.5 Loctite or similar glue may be used to affix screws. Body must be removable for tech inspection.

    10 – Guide
    10.1 The allowed guide code : CH88B.

    11 – Wiring, Braids and Eyelets
    11.1 The power cables, braids and eyelets to hold the power cables should be Slot.It or Slot.It appearing.
    11.2 A grub screw may be used to hold wires into guide.

    12 – Ballast
    12.1 Weight may not be placed on the outside of the chassis or body.

    13 – Interior
    13.1 “Modern LMP” cars must use stock or replacement full interior specific to the model entered. No Lexan interiors.

    Final Rule, if it does not mention it, it means you cannot do it
    Last edited by The Professor; 12-28-2016, 08:39 AM. Reason: updated LMP spec
sex vidio
antalya escort
lara escort escort istanbul escort sirinevler escort antalya
atasehir escort taksim eskort lara eskort bayan bakirkoy bayan eskort
gaziantep escort
gaziantep escort
erotik film izle Rus escort gaziantep rus escort
istanbul escort
kadikoy escort kartal escort
Blonde and brunette dirty 3some in semi obscure Профессор трахнул студенту толстым хером pelicula embarazada por accidente